Shenzhen Jingbo Mechanical & Electrical CO.,Ltd
Try our best to offer customers excellent products, good price and great service
Add to Cart
Stepper Digital Driver JB3722M AC110-220V 7.0A 300 Microsteps Matching 3phase stepper motor size 57mm, 86mm, 110mm and 130mm
Features
◆High performance, low price
◆16 channels constant angle and constant torque microstep, max revolution is up to 60,000 pulse/R
◆Driving current can be adjusted from 1.2A/phase to 7.0A/phase through 16 channels
◆Upmost response frequency amounts to 200Kpps
◆Once the pulse stops over 100ms, the phase current will be automatically reduced to half of pre-set current
◆Opto-isolated signal Input/Output
◆Single power input, voltage range: AC110-220V
◆It can match 3 phase hybrid stepper motors whose current is under 7A, flange size ranges from 57mm to 130mm
◆Phase memory function (Note: Once the input stops over 3 seconds, the driver will memorize the motor phase automatically so that it can restore the phase automatically when it is repowered or MF signals change from low level to high level.)
Wiring and Dimension example
Current setting
The working current of the driver is set by DIP-1 terminal, for more details please refer to the diagram below. (Note: the value is RMS)
Current (A) | 1.2 | 1.5 | 2.0 | 2.3 | 2.5 | 3.0 | 3.2 | 3.6 | 4.0 | 4.5 | 5.0 | 5.3 | 5.8 | 6.2 | 6.5 | 7.0 |
D1 | OFF | OFF | OFF | OFF | OFF | OFF | OFF | OFF | ON | ON | ON | ON | ON | ON | ON | ON |
D2 | OFF | OFF | OFF | OFF | ON | ON | ON | ON | OFF | OFF | OFF | OFF | ON | ON | ON | ON |
D3 | OFF | OFF | ON | ON | OFF | OFF | ON | ON | OFF | OFF | ON | ON | OFF | OFF | ON | ON |
D4 | OFF | ON | OFF | ON | OFF | ON | OFF | ON | OFF | ON | OFF | ON | OFF | ON | OFF | ON |
Microstep setting
The microsteps of the driver are set by DIP2 terminal with the following 16 channels. They are set separately by the first 4 of the 6 DIP-switch.(The other 2 are for function setting). Details are as below: Microsteps(pulse/R)
Microstep | 400 | 500 | 600 | 800 | 1000 | 1200 | 2000 | 3000 | 4000 | 5000 | 6000 | 10000 | 12000 | 20000 | 30000 | 60000 |
D1 | ON | ON | ON | ON | ON | ON | ON | ON | OFF | OFF | OFF | OFF | OFF | OFF | OFF | OFF |
D2 | ON | ON | ON | ON | OFF | OFF | OFF | OFF | ON | ON | ON | ON | OFF | OFF | OFF | OFF |
D3 | ON | ON | OFF | OFF | ON | ON | OFF | OFF | ON | ON | OFF | OFF | ON | ON | OFF | OFF |
D4 | ON | OFF | ON | OFF | ON | OFF | ON | OFF | ON | OFF | ON | OFF | ON | OFF | ON | OFF |
D5 | ON, Double pulse: PU is clockwise pulse signal, DR is counterclockwise pulse signal | |||||||||||||||
OFF, single pulse: PU is step pulse signal, DR is direction signal | ||||||||||||||||
D6 | Self detect switch (OFF: accept external signal, ON: the driver is running at 30R/M internal) | |||||||||||||||
Input signal timing diagram
Terminal function
Port | Pin No | Mark | Function | Notes |
DB15 | 1 | PU+(5V) | Step pulse signal+ | It can connect +5V or +24V, but an extra resistor is needed if it connect +24V |
2 | PU-(5V) | DP5=OFF, PU is pulse signal | Effects on falling edge, the motor goes one step as the pulse input change from “high” to “low”. Input resistance is 220Ω. Requirement: low voltage:0-0.5V, high voltage:4-5V, pulse width >2.5μs | |
DP5=ON, PU is clockwise pulse signal | ||||
3 | DR+(5V) | Direction control signal+ | It can connect +5V or +24V, but an extra resistor is needed if it connect +24V | |
4 | DR-(5V) | DP5=OFF, DR is direction control signal | Change motor’s direction of rotation. Input resistance is 220Ω. Requirement: low voltage:0-0.5V, high voltage:4-5V, pulse width >2.5μs | |
DP5=ON, DR is counterclockwise pulse signal | ||||
5 | MF+(5V) | Motor Free signal+ | It can connect +5V or +24V, but an extra resistor is needed if it connect +24V | |
6 | MF-(5V) | Motor Free signal- | Once effects, it will cut off the motor current, the driver stops working and sets the motor free | |
7,8 | NC | NC | NC | |
9 | PU+(24V) | Step pulse signal+ | It can connect +24V pulse signal power supply | |
10 | PU-(24V) | DP5=OFF, PU is pulse signal | Effects on falling edge, the motor goes one step as the pulse input change from “high” to “low”. Input resistance is 1.8KΩ. Requirement: low voltage:0-0.5V, high voltage:24V, pulse width >2.5μs | |
DP5=ON, PU is clockwise pulse signal | ||||
11 | DR+(24V) | Direction control signal+ | It can connect +24V direction signal power supply | |
12 | DR-(24V) | DP5=OFF, DR is direction control signal | Change motor’s direction of rotation. Input resistance is 1.8KΩ. Requirement: low voltage:0-0.5V, high voltage:24V, pulse width >2.5μs | |
DP5=ON, DR is counterclockwise pulse signal | ||||
13 | MF+(24V) | Motor Free signal+ | It can connect +24V motor free signal power supply | |
14 | MF-(24V) | Motor Free signal- | Once effects, it will cut off the motor current, the driver stops working and sets the motor free | |
15 | NC | NC | NC | |
Motor, power port | 1 | U | Connect to the motor | |
2 | V | |||
3 | W | |||
4 | PE | Ground wire | Ground | |
5、6 | L、N | Power supply | Power: AC110-220V |
! Caution
1. The input voltage can not exceed AC220V .
2. The input pulse signal effects on falling edge
3. ALM lights and the driver stops working when the driver temperature is over 75℃. Until the temperature falls to 50℃, it will restart to work after powered-up. The heat sink is needed when overheat occurs
4. ALM lights if it is short circuit, please check motor leads and eliminate other short faults, and then repower up to restore
5. ALM lights if the motor does not connect well with the driver, please check motor leads and repower up to restore